The Frëtt team will donate part of the profits to Deuil Jeunesse Quebec.
27.89 $ CA
* in the process of BNQ attestation (continuous batches attestations)
IMPORTANT NOTICE: This mask is in the process of being attested by the BNQ and we cannot determine the exact date on which the lots will be approved. This situation is unfortunately out of our control. If it’s mandatory for you to wear a BNQ approved face cover in your workplace, we invite you to subscribe to our newsletter HERE and stay informed on the release date. Alternatively, you can get this mask today as it meets the ASTM F3502-21 International Standards for workplaces.
Exceptional comfort and optimal sealing provided by the 3D ergonomic shape. This ultralight and stylish eco-efficient barrier face covering has been designed to offer incredible breathability made possible among others by the maximized air exchange surface while providing high-performance and regulation-compliant filtering protection.
Breathability (Differential pressure) (EN 14683:2019) (BNQ 1922-900): 5.3 mmH2O/cm2
Filtration PFE* fine particles (BNQ 1922-900 : TPPP*** 20nm to 800nm): 81 %
Filtration Coarse particles (3 microns +): 100 %
Breathability (Differential pressure) (ASTM F3502-21): 9.5 mmH2O
Filtration PFE* fine particles (ASTM F3502-21 : Fixed at 75nm**): 82 %
Flammability (HMIS recommandation: ≤ 1): ëTECH= HMIS 1
* PFE : Particles Filtration Efficiency
** ASTM F3502-21 : Monodispersed flux of single-sized NaCl particles at 75 nm (nanometers) Level 2 = this ASTM standard’s highest level of performances
*** TPPP : filtration % of the size of the most penetrating particles (BNQ : polydispersed flux of NaCl particles ranging from 20 to 800 nm)
Proudly created and produced in Canada
Wash hands with soap for at least 20 seconds before putting it on and after touching it. Rinse and dry.
Handle the mask with the head harness or elastics for putting on and taking off. Avoid touching the inside.
Ensure the optimal fit of the mask to completely cover the nose and mouth, as well as to prevent leaks and avoid having to replace the mask.
Place the face cover over your nose and mouth and the elastic bands around your ears ou head (depending on model).
Adjust the elastics while keeping the face cover well-centered.
Press the metallic wire onto your nose.
Ensure that you have a good seal around the face cover. The edge with the metal wire insert must be on top and be worn on your nose.
If necessary, use an accessory to improve your comfort or reduce pressure on your ears.
Do not touch the face cover again until you take it off.
Place it in a sealed bag until you can wash it.
“ MEETS ASTM F3502, SPECIFICATION FOR BARRIER FACE COVERINGS. THIS PRODUCT IS PRIMARILY IN- TENDED AS A MEANS OF SOURCE CONTROL FOR MINIMIZING THE PROJECTION OF EXPELLED MATERIALS FROM THE WEARER’S NOSE AND MOUTH. WARNING: THIS BARRIER FACE COVERING IS NOT A MEDICAL FACE MASK AS DEFINED IN ASTM F2100, IS NOT INTENDED FOR USE IN MEDICAL PROCEDURES, AND IS NOT A RESPIRATOR. ”
Machine wash in warm or hot water at gentle cycle, using regular or natural laundry detergent.
If necessary, tie the elastic loops to ensure they don’t come off in the machine.
Ideally place the mask(s) in a mesh or net bag and wash with clothes or towels to increase durability.
Place the face cover(s) in a mesh or net bag and wash it with light colored clothes or towels that are not too dirty to increase durability.
Do not use fabric softener.
Hang or lay flat to dry.
Wash or discard safely the bag used to carry the face cover.
When hesitating between 2 sizes, it is recommended to choose the larger one to insure proper breathability and fit.
The user shall choose the proper model or proper size to cover their face from nose to chin and allow proper fit of the top, sides and bottom of the face covering.
It is recommended to change the mask if it is wet, visibly dirty, damaged or if breathing is difficult; moisture in materials affects breathability.
It is recommended that you do not wear a face cover for more than four hours.
Wearing a mask does not replace hand washing, respiratory etiquette and environmental cleanliness. Wearing a face covering should not reduce efforts to promote physical distance.
The same mask should only be used by the same person.
Not following cleaning conditions and safe use decreases the protection offered by the face covering and increases the risk of infection.
Barrier face coverings should not be placed on very young children (<2 years) or anyone who has trouble breathing, or anyone who is unconscious, incapacitated, or otherwise unable to remove the barrier face covering without assistance.
Barrier face coverings with Level 1 airflow resistance may not be suitable for children or for adults that have difficulty breathing and a barrier face covering with Level 2 airflow resistance is recommended.
Barrier face covering contains metal and should not be worn during MRI procedures.
In order to stay informed on our latest products and news, please fill out the form below