fbpx
Logo Frett Solutions
WHOLESALE ORDERS
Cart
My account

DELIVERY ALL OVER AMERICA & EUROPE – FREE SHIPPING ON ALL ORDERS OF $ 150 AND MORE

Online Store

Technical sheet
inside outside grafic
Reusable face mask ëPRO
inside outside grafic
Reusable face mask ëPRO
 

AVAILABLE FOR SMALL FACES OR CHILDREN

Zoom image

ëAIR

US $ 27.50

Clear

Prices degressive according to quantity.

For orders of 250 units or more, click here

CHILDREN & ACTIVE PEOPLE’S FAVORITE

 

COMPLIANT / MEET STANDARDS REQUIREMENTS AFTER 100 WASHES:

ASTM F3502-21** (LEVEL 2) / AFNOR SPEC S76-001 / EN 14683:2019 (LEVEL II)

FEATURES & BENEFITS

  • Very large air interface for unparalleled breathability and efficient filtration.
  • The mask fabric will not obstruct your mouth during speaking or exertion.
  • Lightweight and effective metal nose bar. 
  • Adjustable elastic ear bands with possible additional accessories for optimizing protection while enhancing comfort.
  • Ultralight, compact design similar to disposable masks but with 5 side pleats for enhanced leak tightness and ergonomy.
  • Large amplitude from top to bottom for long faces.
  • Ultimate comfort, all-day wear (8 hours a day)
  • Engineered to reduce moisture inside the face cover to maintain the integrity of its protective barrier.

 

SCIENTIFIC RESULTS (always tested after 100 washes)

Filtration coarse particles (droplets from 0.8 µm): 99 %  

Filtration fine particles (0.075 µm / 75 nm NaCl aerosols): 55-67 % PFE* (level 2 ASTM F3502) 

Breathability (differential pressure): 5 mmH2O (level 2 ASTM F3502) / 4.1 mmH2O/cm2 (EN 14683)

Flammability: Class 1 according to 16 CFR PART 1610

Fluid resistance (penetration): 80 mmHg according to ASTM F1862 

TESTED  in ISO 17025 CERTIFIED laboratories

CONTEXTS

Children (travels, schools…), sustained sports activities, physical efforts and for handling work, delicate respiratory health, phone calls or conferences, public transport, hot climates, working environments with social distancing, extended wear, pollution, allergies

* PFE : Particles Filtration Efficiency
** ASTM F3502-21 test is performed on whole devices (masks) using NaCl particles at a flow rate of 85 LPM.

3 LIFE CYCLES & ZERO WASTE

Workplace => Personal => Recycling

When worn out after personal use, mail the mask to us or put it in a dedicated collection box for 100 % recycling. Our plastic accessories are made with recycled polypropylene from our fabric scraps. The nasal strips are returned to us for reuse in production.

CUSTOMIZATION (contact us)

– 250 units and more: labels with your logo on the side of the mask

– 2 000 units and more: personalized colors and prints

Prices and deadlines according to the project

Proudly created and manufactured in Canada

ëncore technology Frëtt Solutions

  • Wash hands with soap for at least 20 seconds before putting it on and after touching it. Rinse and dry.

 

  • Handle the mask with the head harness or elastics for putting on and taking off. Avoid touching the inside.

 

  • Ensure the optimal fit of the mask to completely cover the nose and mouth, as well as to prevent leaks and avoid having to replace the mask.

 

  • Place the face cover over centred on your nose and mouth and the elastic bands around your ears ou head (depending on model). 

 

  • The edge with the metal wire insert must be on top and be worn on your nose.

 

  • Adjust the elastics while keeping the face cover well-centered.

 

  • Press the metallic wire onto your nose.

 

  • Ensure that you have a good seal around the face cover, loosen or tighten the elastics or bands if necessary.

 

  • Test for leaks. If you have glasses, put them on and if it is fogged, tighten the elastics or bands and / or press the nose wire more.

 

  • If necessary, use an accessory for the head circumference or to reduce the pressure behind the ears for more comfort. These accessories allow the mask to be tightened more, reducing leakage.

 

  • Do not touch the face cover again until you take it off.

 

  • After wearing your face cover, place it in a mesh bag, then a closed bag until you can wash it.

 

  • Check the condition of the face cover(s) after each wash. Restore it to its initial shape before hanging drying.  If any part appears worn, pierced, unstitched or damaged, it is then time to use a new one and discard this one. Unless it appears to be a stitch that can easily be repaired, you should dispose of the face cover in a zero waste box provided for this purpose.

 

“ MEETS ASTM F3502, SPECIFICATION FOR BARRIER FACE COVERINGS. THIS PRODUCT IS PRIMARILY IN- TENDED AS A MEANS OF SOURCE CONTROL FOR MINIMIZING THE PROJECTION OF EXPELLED MATERIALS FROM THE WEARER’S NOSE AND MOUTH. 

WARNING: THIS BARRIER FACE COVERING IS NOT A MEDICAL FACE MASK AS DEFINED IN ASTM F2100, IS NOT INTENDED FOR USE IN MEDICAL PROCEDURES, AND IS NOT A RESPIRATOR. ”

  • Machine wash or dry heat before each use. 

 

  • Combinations of both disinfection modes are possible as well (e.g. 1 machine wash every 5 dry heats ).

 

  • Machine wash: Delicate cycle, water temperature ≥ 40-70°C. Minimum 30-minute cycle.

 

  • Use regular or natural detergent, no softener, no bleach, no additives.

 

  • Place in a mesh bag and wash with pale clothes that are not too dirty to increase durability.

 

  • Hang or lay flat to dry.

 

  • Dry heat maintenance: preheat the oven to 93°C (200°F); when the temperature is reached and verified with a thermometer placed inside the oven, put the mask(s) on a clean rack or parchment paper and leave for 30 minutes.

 

  • Take out of the oven and let cool for 5 minutes.

 

  • Mind the proximity or contact with heating elements.

 

  • Wash or safely dispose of the bag used to transport the soiled mask.

 

  • Store in a clean, dry place, avoid heat above 100°C (212°F).
  • The user shall choose the proper model or proper size to cover their face from nose to chin and allow proper fit of the top, sides and bottom of the face covering. (See the size chart)

  • It is recommended to change the mask if it is wet, visibly dirty, damaged or if breathing is difficult; moisture in materials affects breathability.

  • It is recommended that you do not wear an etrëma by Frëtt Solutions face cover for more than eight (8) hours per day.

  • Wearing a mask does not replace hand washing, respiratory etiquette and environmental cleanliness. Wearing a face covering should not reduce efforts to promote physical distance.

  • Not following cleaning conditions and safe use decreases the protection offered by the face covering and increases the risk of infection. Frëtt Solutions or its retailers / representatives are in no way responsible for the consequences of improper use of etrëma products.

  • Barrier face coverings should not be placed on very young children (<2 years) or anyone who has trouble breathing, or anyone who is unconscious, incapacitated, or otherwise unable to remove the barrier face covering without assistance.

  • Barrier face covers with ASTM F3502-21 airflow resistance level 1 may not be suitable for children or adults who have difficulty breathing and barrier face covers with ASTM F3502-21 level 2 resistance to air flow is then recommended.

 

  • Barrier face covering contains metal (copper) and should not be worn during MRI procedures.

Related products

ear saver Frëtt Solutions
Back Head Extender
US $ 3.00
Select options
Draw cord Frëtt Solutions black
Adjustable Drawcord
US $ 5.00
Select options
Laundry Mesh Bag
US $ 6.00
Select options
Canvas Bag
US $ 6.00
Select options

Join our community

Sign up to our newsletter to stay informed about our projet evolution, our environmental actions,
and of course, our promotions.

HELP
MY ACCOUNT
Logo Frett Solutions blanc
solutions@frettdesign.ca
Facebook Instagram Linkedin

The Frëtt team will donate part of the profits to Deuil Jeunesse Quebec.

© 2021 Copyrights Frëtt Solutions | website by : SMT Web & Marketing

Top of page